AGP Picks
View all

FIDER pitches parallel feeder system for high-mix assembly lines

Oct. 29, 2026
FIDER pitches parallel feeder system for high-mix assembly lines
By AI, Created 20:36 UTC, Oct 29, 2026, AGP -

FIDER is promoting a parallel flexible feeder system for manufacturers that need to handle multiple small parts at once in a single robotic station. The company says the setup can reduce bottlenecks, cut changeover downtime and support high-mix production in connector, sensor and medical device assembly.

Why it matters: - High-mix assembly lines often need multiple dissimilar parts delivered to one robot at the same time. - FIDER says a parallel feeder layout can reduce part starvation, limit changeover stoppages and improve uptime in small-parts production. - The approach is positioned for operations assembling connectors, sensors and medical devices, where throughput depends on handling mixed part geometries without slowing the cell.

What happened: - FIDER outlined a Parallel Flexible Feeder System designed for high-mix, small-parts manufacturing. - The system uses two or more independent multi-axis vibrating feeder platforms in a shared robotic workspace. - The company says the configuration supports simultaneous feeding of different component types beneath an overhead manipulator. - FIDER directs readers to detailed technical specifications at the company’s technical page for engineering consultation.

The details: - Each feeder platform can use dedicated voice-coil or electrodynamic actuators to tune vibration for specific part masses. - The architecture can include segregated optical inspection zones, either with separate cameras or a wide-field sensor with split illumination. - Independent bulk hoppers replenish feeder trays based on optical density measurements. - A centralized programmable logic controller coordinates robot trajectory planning across all active feeding zones. - The parallel setup allows heavier metal stampings and lighter plastic clips to feed at the same time without interfering with each other. - FIDER says the system can support a high-speed Delta robot or a dual-arm gantry in a single workstation. - The company says cell production can reach 50 to 75 assemblies per minute when material presentation is synchronized inside the robot operating envelope. - FIDER says the system can achieve placement tolerances of ±0.05 mm.

Between the lines: - The pitch is less about a single feeder upgrade and more about re-architecting the cell for mixed-part flow. - Independent control loops matter most when one product uses more of one part than another, such as four pins for every housing. - The parallel model also reduces dependence on buffer conveyors, kitting steps and sequential feeding. - FIDER is also framing the system as a resilience play, not just a speed play, because one feeder can keep running while another is cleaned or serviced. - The modular design suggests the target buyer is a factory balancing floor-space pressure, frequent recipe changes and uptime risk.

What's next: - FIDER says manufacturers should compare part geometry diversity, changeover frequency and payback periods before choosing between a single feeder and a parallel system. - The company says parallel feeding is best suited to lines with two or more subcomponents, ten or more product variants or cleanroom environments where space is limited. - Facilities interested in the setup can review specifications and schedule an engineering consultation through the company’s website.

The bottom line: - FIDER is betting that high-mix manufacturers will trade higher system complexity for less downtime, faster changeovers and better multi-part feeding control.

Disclaimer: This article was produced by AGP Wire with the assistance of artificial intelligence based on original source content and has been refined to improve clarity, structure, and readability. This content is provided on an “as is” basis. While care has been taken in its preparation, it may contain inaccuracies or omissions, and readers should consult the original source and independently verify key information where appropriate. This content is for informational purposes only and does not constitute legal, financial, investment, or other professional advice.

Sign up for:

Healthcare Industry Today

The daily local news briefing you can trust. Every day. Subscribe now.

By signing up, you agree to our Terms & Conditions.

Share this page:

Advanced Search Options

Search for:

Search scope:

Type:

Search in:

Date range:

The last

Sort by:

Sign up for:

Healthcare Industry Today

The daily local news briefing you can trust. Every day. Subscribe now.

By signing up, you agree to our Terms & Conditions.